Кабел: Разлика помеѓу преработките

Избришана содржина Додадена содржина
Создадена страница со: {{во изработка}} {{other uses}} Image:ElectricWireGrounded.jpg|thumb|Крај на три јадрен кабел [[Electrical wiring|ел...
(нема разлика)

Преработка од 00:55, 27 септември 2013

Кабел е најчесто две или повеќе жици едно до друго, брзани, искривени или во плетенка заедно составени, но исто така се однесува на тешко и силно јаже. Во механиката, каблите, инаку познати како жичано јаже, се користат за дигање, влечење, and шлепање или пренесување на сила со затегнување. Во електротехниката каблите се користат за пренос на електрична струја. Оптичките кабли содржат едно или повеќе оптички влакан во заштитната обвивка која ги држи влакната.

Крај на три јадрен кабел електричен систем во TN-S
6 инчи(15 cm) надворешен дијаметар, oil-cooled кабли, поминуваат преку Grand Coulee Dam текот. Пример за тежок кабел за пренос на електрична енергија.
Пожар тест во Шведска, приказ на рапиден оган кој се шири преку горење на заштитени кабли. Од голема важност за каблите кои се користат во инсталациите.
500,000 circular mil (254 mm2) единечен проводник кабел за напојување

Електричните кабли тука се главно наменети за инсталација во згради и индустриски капацитети. За пренос на електрична енергија на оддалеченоста поголема од неколку километри видете високо-напонски кабел, моќни кабли, и HVDC.

Историја

јажињата се направени од повеќе видови на природни влакна како што се коноп, сисла, манила, и памук и се користат за подигнување и влечење. Во 19-от век продлабочувањето на рудниците и изградбата на големи бродови ја зголемило побарувачката за посилни кабли. Откривањето на подобрите челични направени со високо квалитетен челик и достапни по ниска цена, така јажињата станаа честа примена во рударството и другите индустриски дејности. До средината на 19-от век, производството на големи подводни телеграфски кабли беше направено со користење на машини слични на оние што се користат за производство на механички кабли.

Во 19-от и полетокот на 20-от век, електричните кабли често пати биле изолирани со користење на крпа, гума и хартија. Пластични материјали обично се користат и денес, освен за високо-сигурносните енергетски кабли.

Електрични кабли

 
Пресек на електричен кабел

електричните кабли може да се направат пофлексибилни составени од жици. Во овај процес, помали индивидуални жици се извиткани или во плетенка заедно прават поголеми жици кои се пофлексибилни од вистинските жици со слична големина. Врзаните во сноп мали жици како составен дел даваат повеќе флексибилност. бакарни жици во кабел можат да бидат голи, или може да бидат обложени со тенок слој на друг метал, најчесто калај но понекогаш злато, сребро или некој друг материјал. Бакар, злато и сребро се многу помалку склони кон оксидација од бакарот, кој што може да го продолжи животот на жицата, и го прави лемењетополесно. Калајот исто така се користи за да обезбеди подмачкување помеѓу жиците. Калајот исто така се користи и во отстранување на гумената изолација. Тесната положба го прави кабелот растеглив (CBA – како жиците во телефонска слушалка).Предлошка:Elucidate

Cables can be securely fastened and organized, such as by using trunking, cable trays, cable ties or cable lacing. Continuous-flex or flexible cables used in moving applications within cable carriers can be secured using strain relief devices or cable ties.

At high frequencies, current tends to run along the surface of the conductor. This is known as the skin effect.

Cables and electromagnetic fields

 
Coaxial cable.
 
Twisted pair cabling

Any current-carrying conductor, including a cable, radiates an electromagnetic field. Likewise, any conductor or cable will pick up energy from any existing electromagnetic field around it. These effects are often undesirable, in the first case amounting to unwanted transmission of energy which may adversely affect nearby equipment or other parts of the same piece of equipment; and in the second case, unwanted pickup of noise which may mask the desired signal being carried by the cable, or, if the cable is carrying power supply or control voltages, pollute them to such an extent as to cause equipment malfunction.

The first solution to these problems is to keep cable lengths in buildings short, since pick up and transmission are essentially proportional to the length of the cable. The second solution is to route cables away from trouble. Beyond this, there are particular cable designs that minimize electromagnetic pickup and transmission. Three of the principal design techniques are shielding, coaxial geometry, and twisted-pair geometry.

Shielding makes use of the electrical principle of the Faraday cage. The cable is encased for its entire length in foil or wire mesh. All wires running inside this shielding layer will be to a large extent decoupled from external electric fields, particularly if the shield is connected to a point of constant voltage, such as earth. Simple shielding of this type is not greatly effective against low-frequency magnetic fields, however - such as magnetic "hum" from a nearby power transformer. A grounded shield on cables operating at 2.5 kV or more gathers leakage current and capacitive current, protecting people from electric shock and equalizing stress on the cable insulation.

Coaxial design helps to further reduce low-frequency magnetic transmission and pickup. In this design the foil or mesh shield has a circular cross section and the inner conductor is exactly at its center. This causes the voltages induced by a magnetic field between the shield and the core conductor to consist of two nearly equal magnitudes which cancel each other.

A twisted pair has two wires of a cable twisted around each other. This can be demonstrated by putting one end of a pair of wires in a hand drill and turning while maintaining moderate tension on the line. Where the interfering signal has a wavelength that is long compared to the pitch of the twisted pair, alternate lengths of wires develop opposing voltages, tending to cancel the effect of the interference.

Fire protection

In building construction, electrical cable jacket material is a potential source of fuel for fires. To limit the spread of fire along cable jacketing, one may use cable coating materials or one may use cables with jacketing that is inherently fire retardant. The plastic covering on some metal clad cables may be stripped off at installation to reduce the fuel source for fires. Inorganic coatings and boxes around cables safeguard the adjacent areas from the fire threat associated with unprotected cable jacketing. However, this fire protection also traps heat generated from conductor losses, so the protection must be thin.

There are two methods of providing fire protection to a cable:

  1. Insulation material is deliberately added with fire retardant materials
  2. The copper conductor itself is covered with mineral insulation (MICC cables)

Electrical cable types

Basic cable types are as follows:

Shape
Construction

Based on construction and cable properties, they can be sorted into the following:

Special

Application

 
A 250V, 16A electrical cable on a reel.


See also

References

Further reading

  • R. M. Black, The History of Electric Wires and Cables, Peter Pergrinus, London 1983 ISBN 0-86341-001-4
  • BICC Cables Ltd, "Electric Cables Handbook", WileyBlackwell; London 3rd Edition 1997, ISBN 0-632-04075-0

External links

Cable Jacket Types Explained w/ Reference Chart

Предлошка:Link GA